Search Results

Search Again
Page 7 of 8
  1. SandyFloor
    Post

    Lvt lads

    Easiest way is put a joint in it. Imagine you're doing a tiny room and start with the off cut of the previous line
    Post by: SandyFloor, May 16, 2013 in forum: Vinyl / Impervious floor coverings
  2. SandyFloor
    Post

    Which Karndean this??

    I think it's RP71 Columbian Pine. It was last in 2008 catalogue. There might be some online...
    Post by: SandyFloor, May 16, 2013 in forum: Pictures
  3. SandyFloor
    Post

    Gapping LVTs

    Dog doesn't look too happy but who would with that haircut? Looks like the canine reincarnation of Jimmy Savile! Nice job as usual Darren.
    Post by: SandyFloor, May 5, 2013 in forum: Vinyl / Impervious floor coverings
  4. SandyFloor
    Post

    Karndean border

    I can't see it either....who stuck selotape on your floor?
    Post by: SandyFloor, May 3, 2013 in forum: Vinyl / Impervious floor coverings
  5. SandyFloor
    Post

    Removing Kardnean and Plyboard Screwed to floorboards

    I think the noise is simply due to Karndean being hard flooring and bare floorboards would be even noisier so I can't see the point of uplifting...
    Post by: SandyFloor, May 2, 2013 in forum: Vinyl / Impervious floor coverings
  6. SandyFloor
    Post

    Removing Kardnean and Plyboard Screwed to floorboards

    Is it being replaced with carpet?....if so why not just fit over it?
    Post by: SandyFloor, May 1, 2013 in forum: Vinyl / Impervious floor coverings
  7. SandyFloor
    Post

    Steps in Karndean

    The time was in the prep of the ply. The raised section went round three walls. The awkward part was getting an even curve at the corners....
    Post by: SandyFloor, Apr 30, 2013 in forum: Vinyl / Impervious floor coverings
  8. SandyFloor
    Thread

    Steps in Karndean

    [ATTACH] [ATTACH] Some steps I did in Knight Tile as a part of a large living room. The treads and risers I clad in 9mm ply and sanded to...
    Thread by: SandyFloor, Apr 30, 2013, 11 replies, in forum: Vinyl / Impervious floor coverings
  9. SandyFloor
    Post

    US tools

    I looked into this a few years ago and that's pretty much what I discovered. What wasn't clear was the difference in efficiency but seems quite small
    Post by: SandyFloor, Apr 18, 2013 in forum: Tool Chat
  10. SandyFloor
    Post

    Hemihydrate screed

    I've tiled on them a couple of times in the past and you can't get much smoother or flatter. It's because it's so fluid when it's poured.
    Post by: SandyFloor, Apr 3, 2013 in forum: Subfloor Preparation
  11. SandyFloor
    Post

    Hemihydrate screed

    I've never heard of it either.One for the addy manufacturer methinks
    Post by: SandyFloor, Apr 2, 2013 in forum: Subfloor Preparation
  12. SandyFloor
    Post

    Annoying gapping

    Some modern conservatories aren't as bad with the type of glass used which somehow prevents them turning into greenhouses whenever the sun blinks....
    Post by: SandyFloor, Mar 26, 2013 in forum: Vinyl / Impervious floor coverings
  13. SandyFloor
    Post

    Ceramics

    It seems simple on the surface ( pardon the pun ) but there are many pitfalls most of them to do with preparation. Does that sound familiar?
    Post by: SandyFloor, Mar 25, 2013 in forum: General Flooring Chat
  14. SandyFloor
    Post

    2 big days

    Were you on your ownsome?
    Post by: SandyFloor, Mar 25, 2013 in forum: Vinyl / Impervious floor coverings
  15. SandyFloor
    Post

    Mixer option?

    Way low on oomph! Your average promixer is around the 1000w mark
    Post by: SandyFloor, Mar 15, 2013 in forum: Tool Chat
  16. SandyFloor
    Post

    Refitting carpet

    I'll be fine now thanks
    Post by: SandyFloor, Mar 15, 2013 in forum: Carpet / Textile
  17. SandyFloor
    Post

    Nice !!!!!!

    I've heard that about you!
    Post by: SandyFloor, Mar 15, 2013 in forum: Pictures
  18. SandyFloor
    Post

    Nice !!!!!!

    Personally I judge it one the condition of the plumbing. If it looks to be in good order I'll disconnect and reconnect and check thoroughly for...
    Post by: SandyFloor, Mar 15, 2013 in forum: Pictures
  19. SandyFloor
    Post

    Nice !!!!!!

    Not me it won't. When I get to the stage my kitchen is like that I'm going to shoot myself in the head with a Paslode. Just had a look at my...
    Post by: SandyFloor, Mar 15, 2013 in forum: Pictures
  20. SandyFloor
    Post

    Refitting carpet

    If only I'd read that I could have saved myself so much torment lol
    Post by: SandyFloor, Mar 15, 2013 in forum: Carpet / Textile
Showing results 121 to 140 of 156 Next >
Search Again
Page 7 of 8